CCTV Tester Pro Especificações

IP/CCTV Tester Manual V2.10

2 2.5 Front Pan IP/CCnel CTV Tester Use6 r’s Manual

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 IP/CCOSD menu The charge indicis complete, theThe data-transmThe data-re

IP/CCTV Tester User’s Manual 8 21 Near focus: Focus the image nearby 22 Far focus: Focus the image faraway 23 Menu key 24 TELE: zoom out the

26 Vid27 Vid28 Nu29 Ou30 RS31 LE32 RS33 Ne34 US35 Re36 Eth37 Eth38 Au39 Re IP/CC deo input (BNC inpdeo output (BNC

3 3、Operatio3.1 InstallinThe tester has acompartment) iPrior to using thThere is no neePressing Notice：OnlyThe first timebattery (4

3 3 3.2 Quick Tes Connectdisplay o To drivetransmitimage w To test atester’s RPTZ con3.3 Turn on th Press the key Press the keytimeout du

3DkcaIfP PInPPeIfPN  Once the menthe key  In various fun Functions tha The squares tFirst page m 3.3.1 PTZ contrDisplay the video inke

A UththCBMPCM(6DEEFGMtoHMPP Ath A. Protocol Use the Up and Dowhe “protocol ”. Selehirty PTZ protocolsCSR600、PanasonicB. Port Move the yellow c

SABcPREPtopTaT Cita c  Press th Press th Press th Press th1) Set and GoSetting a PTZ locatA. P/T/Z the cameraB. Press the key urso

OR AR 3PP TP“th 3P OSD Menu of DomReference only) After accessing the dRefer to the dome ca3.3.2 Color bar Press the keyPress the

CAMERA WIZARD II TESTS IP CAMERA TESTS  IP address scan: Scan IP cameras and network device’s for IP address  Link monitor: Displays all IP a

Dco 3P Psefu  Use this The Vidresult inresult in Adjust thDepending on the tyhange between NTof Radio Engineers)3.3.4 PTZ addre

NPthPththPthMwP 3WtoRm 3WTc Note：This functionPress the keyhe PTZ camera’s sePress the butthe PTZ camera willhrough the search. P

3WredN 3Po APm 3.3.7 Video recoWith video present, ecording, saving thedisappears. The file Note: Press the but3.3.8 Record plaPress

3Ceto IfthtoreAPtoncItP 3P 3.3.9 PING TestConnect the CAT5/6nter. Press o adjust the parame f the IP camera or ohe scree

CRse 3Pp AT 3P Connect the CAT5/6Remote adapter (shoerial number of the 3.3.11 Port flickPress to seleport LED blinking sAppl

Tpst AWom 3TFPccsoth 3Pthpc The link monitor dispress to start tatus is“×”, means tApplication： When adding an IPoccupied. If two devmon

NteteU 3C torapPd Note: PoE power suester’s PSE IN porester’s LAN jack. UTP/SCAN jack. T3.3.15 Data monConnect the device to enter. Pre

3P p 3P PtoAtuKLBA 3.3.16 Time setuPress to selNote：Press photographs and vid3.3.17 Device (tePress to mPress or

RFseF 3P 3Pc a Restore factory settF1 user-defined shorelect, press tF2 user-defined shor3.3.18 USB Photographs and vid3.4 DC12V

bcd3T 3UT 44 b. Only connect t. When the CCTd. For best perfor 3.5 Audio inpTest the audio from 3.6 LED flashUse the ultrabright LTurn o

Contents 1、Safety information ...

IP/CCTV Tester User’s Manual 26 Video Output Mode 1.0 Vp-p Video Level test Level test Video signals measured in IRE (NTSC) or mV (PAL) PTZ co

IP/CCTV Tester User’s Manual 27 Port flicker Port flicker Blink the link LED on a switch port to locate a cable’s port location. IP scan、Link m

CAMERA WIZARD II MODEL VTX455 Byte Brothers, Inc 7003 132nd Place SE Newcastle, WA 98059 (425)917-8380 FAX (425)

3、Operation ...

IP/CCTV Tester User’s Manual 1 1、Safety information Notice  The tester is intended to be used in a responsible and safe manner and not in a

IP/CCTV Tester User’s Manual 2 2.Introduction 2.1 General The Camera Wizard II IP/CCTV tester is designed for the installation and maintenance

IP/CCTV Tester User’s Manual 3 2.3 Functions 2.3.1 Video signal display Display the CCTV image on the built-in high definition 3.5”LCD-TFT 480（

IP/CCTV Tester User’s Manual 4 2.3.8 RS485 data test Analyze the data coming from a RS485/RS422 device. The data is displayed in hexadecimal fo

IP/CCTV Tester User’s Manual 5 display the voltage that the PoE switch or injector is supplying to the IP camera. 2.3.19 LED flashlight Light